- Posts: 122
- Karma: 5
- Thank you received: 15
×
Questions about VS-GW2120/GW1600/GW1202 and WGW1002G GSM Series VoIP Gateway
Recovery adfter Firmware upgrade
6 years 6 months ago #11611
by heizi.lv
Hi,
Sorry for the trouble. Please make sure if the SYS led of slave board flashes or not.
If the SYS led is off, i think the file system of slave board is broken. We need an USB-TTL cable to bring it up. Please prepare an USB-TTL cable and follow the manual to flash system firmware:
www.openvox.cn/pub/misc/tools/Flash%20Vo...0USB-TTL%20cable.pdf
If you need any help, you can add my skype for contact. My skype: This email address is being protected from spambots. You need JavaScript enabled to view it.
Sorry for the trouble. Please make sure if the SYS led of slave board flashes or not.
If the SYS led is off, i think the file system of slave board is broken. We need an USB-TTL cable to bring it up. Please prepare an USB-TTL cable and follow the manual to flash system firmware:
www.openvox.cn/pub/misc/tools/Flash%20Vo...0USB-TTL%20cable.pdf
If you need any help, you can add my skype for contact. My skype: This email address is being protected from spambots. You need JavaScript enabled to view it.
6 years 6 months ago - 6 years 6 months ago #11612
by hexus
SYS led is off
It can blink for 1-2 seconds when i hold reset button and powering on, but after release remain off
Where can i get such cable, or maybe flash devise via tftp without cable ? like any other router using openwrt image ??
It can blink for 1-2 seconds when i hold reset button and powering on, but after release remain off
Where can i get such cable, or maybe flash devise via tftp without cable ? like any other router using openwrt image ??
Last Edit: 6 years 6 months ago by hexus.
6 years 5 months ago - 6 years 5 months ago #11616
by hexus
And another question
1.I found version of *.IMG firmware, other images are *.BIN. Can i use Bin images for flashing my device ?
2. In attached instruction
Notice:
Check “rootmtdblock=/dev/mtdblockX” filed, if it shows “mtdblock6”, then execute “update
second” to flash firmware; if “mtdblock4”, then execute “update first”.
BUT my print says something like
rootmtdblock=/dev/ubiblk0_0
What command should i use for update ?
Thanks .
1.I found version of *.IMG firmware, other images are *.BIN. Can i use Bin images for flashing my device ?
2. In attached instruction
Notice:
Check “rootmtdblock=/dev/mtdblockX” filed, if it shows “mtdblock6”, then execute “update
second” to flash firmware; if “mtdblock4”, then execute “update first”.
BUT my print says something like
rootmtdblock=/dev/ubiblk0_0
What command should i use for update ?
Thanks .
Last Edit: 6 years 5 months ago by hexus.
6 years 5 months ago #11617
by heizi.lv
Hi,
Sorry for the trouble.
1) You can only flash .img firmware.
2) Here are the commands you need if rootmtdblock=/dev/ubiblk0_0 :
setenv ipaddr XXXXX
setenv serverip XXXXX
setenv fsfile wg400-current.img
setenv rootmtdblock /dev/mtdblock4
run updatefirst
mtdparts
nand erase offset size
nand erase 0x00100000 0x00080000
nand erase 0x00180000 0x00080000
reset
Sorry for the trouble.
1) You can only flash .img firmware.
2) Here are the commands you need if rootmtdblock=/dev/ubiblk0_0 :
setenv ipaddr XXXXX
setenv serverip XXXXX
setenv fsfile wg400-current.img
setenv rootmtdblock /dev/mtdblock4
run updatefirst
mtdparts
nand erase offset size
nand erase 0x00100000 0x00080000
nand erase 0x00180000 0x00080000
reset
4 years 7 months ago #14482
by D1m0k
Hi, my board fails after update, and when i connect ttl there is only this strings in console
DDR Training.............................................................Done
eeprom-boot $Version: eeprom-boot_1_00_1
Autoboot from NAND in 1 seconds
Comcerto-1000 >
i can't input anything in console
i have working board, with 2 winbond flash chips (one on c1000_cpu_bd, and other in gsm_m35bd), which of them i need to read and write to the bricked board, what memory blocks i need to write?
DDR Training.............................................................Done
eeprom-boot $Version: eeprom-boot_1_00_1
Autoboot from NAND in 1 seconds
Comcerto-1000 >
i can't input anything in console
i have working board, with 2 winbond flash chips (one on c1000_cpu_bd, and other in gsm_m35bd), which of them i need to read and write to the bricked board, what memory blocks i need to write?
Time to create page: 0.047 seconds